BORA NGX 55 in. Non-Chip Strip Replacement
$21.38
Open up your favorite wine bottle with utmost style and add life to your party by choosing this fantastic BORA NGX NonChip Strip Replacement.
In stock
Description
The non-chip strip makes it easy to eliminate tear-out. Simply press this self-adhesive strip onto the clamp edge and cut. The excess width of the strip will come off so the edge of the non-chip strip sits flat against your blade parallel to your clamp edge.
- Self-adhesive non-chip strip ensures smooth cut with reduced tear-out
- Adheres to bottom side of BORA clamp edge for a clean cut
- Part of the BORA clamp edge system to cut and rip sheets and boards
- Sits flat against blade after initial cut to provide clear cut line of visibility
Additional information
| Weight | 0.02 lbs |
|---|---|
| Dimensions | 55.00 × 0.87 × 0.06 in |
| Color Family | White |
| Ideally Used With | Circular Saws |
| Material | Plastic |
| Model | 544003 |
| Power Tool Accessory Type | Other Accessory |
| Product Length (in.) | 55 in |
| Tools Product Type | Other |
Reviews (86)
86 reviews for BORA NGX 55 in. Non-Chip Strip Replacement
Only logged in customers who have purchased this product may leave a review.
Related products
Saw Accessories
Model# KMS7801
Saw Accessories
Model# BDCMTRS
Saw Accessories
Model# BDCMTTS
Saw Accessories
Model# DWS5100
Saw Accessories
Model# 530401
Saw Accessories
Model# DW3278
Saw Accessories
Model# KMS7214
Saw Accessories
Model# KMS7102
Prince Rowe (verified owner) –
This product was not what I expected. I thought I could use it with the WTX system that I have, but it would mean I would have to doube up on to straight edges. I think they need to make T square accessary for WTX straight edge system,
Alanna Oberbrunner (verified owner) –
I found this guide to be very solid as I did not see any measurable deflection when using it and it worked great as a guide. However, not a great track saw substitute. Using either the Saw Plate or just the guide, I found the cuts to be true. I also found that it helped when using the Saw Plate to use a dry lubricant (I used PTFE) on the guide as this allows the saw move much easier on the guide. The guide itself is easy to set up and when locked down it doesn’t move. Using the Saw Plate ensures that your cuts will be true. (I have been known to drift away from a guide.) I think the clamps that allow the guide to be used at an angle across a piece of plywood were very clever and worked great.However, I found the lack of instructions for setting it us to use like a track saw to be lacking to say the least. The instructions were just pictures without any written explanations of any of the steps. Consequently, it took me quite a while to get the saw(s) set up to see how they worked. In addition, it requires a metric allen wrench to set up a saw on the Saw Plate and this wasn’t included so I had to file down another allen wrench to fit. I set put the ‘non chip strip’ on the guide and tried the saw with 24-tooth blade and had minimal tear-out. However, when I switch to the saw with the 60-tooth blade I did have tear-out. Not sure why. I joined the two sections of the guide together to see how that worked and found the joint was not exact, and I had to file the bottom of the lead edge of the Saw Plate so it would not hang up on the joint.I recommend this product an the basis that you will get straight true cuts using the guide particularly when using the Saw Plate. I would have rated it higher if it in fact eliminated tear-out and the instructions were easier to follow. I also found that the nuts that are held in position when tightening the guides on the Saw Plate can rotate as they are not a snug fit in the slots they sit in.
Hassie Volkman (verified owner) –
This is a great tool. I’ve been fiddling for years with just clamping a long piece of straight wood to plywood when I need to make cuts with any precision. So, three clamps and a bulky piece of wood. It works, but it’s a pain. This tool allows you to clamp on sheet goods up to 4 feet wide and get cutting right away. It seems to clamp on consistently at a right angle, but I’m a bit compulsive, so I do check each time. You will have to do some calculation to know how far to set the clamp from where you need to cut–you have to calculate some offset from your saw’s guide. Unless–you can get the Bora Saw Plate that fits with this. If you have the saw plate, you fit your circular saw to the plate, attach an additional guide to the clamp edge, and after setup, you can set the guide to where you want your cuts. This speeds up the process like crazy, and basically gives you the capabilities of a track saw from your circular saw. Great stuff.
Jade Wolff (verified owner) –
I have used a few different clamp edge guide before so I am familiar with this type of product. This one is the best one that I have used by far. For me, it is the clamping action that makes it stand out. This may seem simple but other manufacturers have not gotten this perfect in my opinion. The clamp holds very tight without squeezing the material too much. Others will either slip because they are not tight enough or they will be so tight that either the edge guide or the material is bowed. Bora gets it perfect!
Chelsie Armstrong (verified owner) –
This Bora 50-inch Clamp Edge Saw Guide is a welcome addition to my woodworking tools. I bought a similar small clamp edge type guide many years ago at a woodworking show in Phoenix, but this Bora clamp edge is far superior to that one. First of all, the Bora NGX is 50 inches long, so it can clamp all the way across a 4 x 8 sheet of plywood. (My old clamp edge guide is only 26 inches long, so it has limited use as a saw guide.) The Bora clamp edge aluminum rail is slightly more than 1/2 inch thick, so it is very sturdy.The main rail of the Bora NGX clamp edge is made of extruded aluminum and the clamping mechanism and end stop are made of some kind of sturdy molded thermo-plastic. When released the clamping end slides easily in the double track slots of the aluminum rail. When you get it in position against the edge of your plywood, a simple flick of the T-handle locks the clamp edge in place ready to guide your saw. Bora sells a separate NGX saw plate that can ride on top of the clamp edge rail or you can just allow for your saw’s blade offset and let the saw’s edge be guided by the clamp edge rail.My only complaint (which is a pet peave of mine) is that Bora slapped a UPC sticker on the clamp edge rail where it meets the cardboard packaging (see photo) that was very hard to remove. It took me 15 minutes of soaking the UPC label remnants with WD40 and scrubbing with paper towels to remove the label adhesive without damaging the aluminum rail’s finish. Sterlite, who makes plastic storage boxes, manages to make labels that stick to the product but are very easy to remove without leaving adhesive residue, so why can’t other manufacturer’s follow their lead?
Nola Nolan (verified owner) –
BORA 5-Piece Clamp Edge Saw Guide. Well built and nice features. When the extension is added, it can handle an eight foot piece of plywood. I dropped this product down a point because the instructions could use a lot more detail. Especially on installing the non-chip strips. Took me a while and a phone call to figure it out. First, straighten the strips out as much as possible. Second, the blue covering needs to be removed from the double sided tape. If your not careful, you’ll remove the tape along with the blue covering. One strip on each guide. Make sure the strip is on the same side of each guide. The side of the strip that has the tape goes on one side of the bottom of the guides (lower step on bottom). When the strip is installed, the tape side of the strip should be level with the upper step of the guide. The other edge of the strip should overhang the edge of the guide. The saw should be used on the side of the guide with the strip attached (overhang). Mounting the saw to the saw plate was easier and is adjustable in all directions. I stored my saw with the plate attached. The adjustible clamp holds the board tightly and gives you a ridgit, straight guide to cut on. Can be used with or without the sawplate. Using the saw plate is easier.
Mario Padberg (verified owner) –
Tried to use it over the weekend on a few sheets of plywood. It seems as if not completly square. There does not seem to be any adjustments to square it off perfectly.
Evangeline Pfannerstill (verified owner) –
Sticks to the guide rail but overall Good saw plate
Joel Purdy (verified owner) –
I have a few different clamps like this. This one is by far the best.
Mariam Sanford (verified owner) –
It’s a bit difficult to set up. A lot of folks recommend using it with a dedicated saw and keeping that saw attached to the plate, which I think would help. But it makes excellent straight cuts, and sets up much faster than my old straight edge.
Mattie Braun (verified owner) –
Easy to use guide clamp that makes accurate cuts quickly. Saw base is easy to mount to your saw and easy to dial in. Great setup for ripping and cutting down plywood.
Travis Marks (verified owner) –
This tool is like having a portable track saw. I most recently used it for ripping and cross cutting sheets of plywood and 4’x8’ PVC trim sheets. And using it with the caddy/sled/sawplate/whatever-you-want-to-call-it, which attaches to the saw, sure beats my previous method. No more fighting an imperfect 2×4 to stay flush. The caddy fits on two of my 7 1/4” saws (one corded, one cordless), as well as my little 6 1/2” cordless. At first I struggled to attach the saws, but that was because I wasn’t lifting the blade. Once attached, you lower the saw blade to make sure there’s reasonable cutting depth (keep in mind the caddy’s clamps should be placed as to not interfere with the saw’s motor/housing etc… I made that mistake too). That brings me to the paper instructions…. Would have been nice if they were clearer. Bora’s website wasn’t any help either… I had to goto youtube to figure it out. There are a lot of fine adjustments required to get the saw perfectly straight in the caddy, so I’ve left my corded saw in it so it’s ready to go for the next project.The guide comes in two pieces, which when combined provides 100”. Keep in mind when you only use the main piece you’ll get a little less than a 50” cut due to the clamps on each end. Would have been nice if this guide had quick change/setup capability to go from 55” to 100”. Assembly to 100″ requires removing a few screws and then screwing the ends together. Of course, then you have to reverse the process to take it apart for storage. I greatly appreciate the hanging hooks on both guides since I can get them out of the way when not in use.The 50” and 100” non-chip adhesive tape strip, is a nice idea in theory. In practice, it’s useless in my opinion unless you (a) adhere it perfectly straight (although it will be kinda straight if not perfect after the first cut); and (b) make only straight cuts. If you do a beveled cut you’ll cut the tape unless you flip the whole sled contraption around to the other side of the track…. and doing so changes the blade’s position. I haven’t tried the two additional track clamps for angle cutting yet because I haven’t needed angular cuts. To attach the track clamps you have to remove the ends and slide them onto the track. Overall this seems well built and it’s a very helpful tool for the DIYer like me who wants the advantages of a track saw. I’m pleased with it.
Elody Dicki (verified owner) –
Purchased this kit to augment a WTX have owned for many years. Clamp mechanism of NGX is much better design IMO and is easy to set. Using the saw sled with Mak 18V LXT sidewinder and this combo works well to add and easy to set up track saw rig for panel work in my pocket shop.
Braeden Wiegand (verified owner) –
Perfect for cutting ACM panel on my drafting table
Heaven Hintz (verified owner) –
Works great especially with worx exactrack circular saw. Cuts through 4 x 8 plywood straight every time!
Brielle Balistreri (verified owner) –
This clamp/guide is invaluable for table saw free environments. I couldn’t recommend it enough!
Roxane Frami (verified owner) –
This guide makes cutting sheets of plywood, oriented strand board and composite siding much easier. In my opinion, this is a must have for the DIY handyman. Matched with the saw sled, you can cut straight edges up to fifty inches. My biggest concern is that the saw sled is made of plastic and I don’t know how much rough use it can handle. I have always had a problem free cutting sheet material squarely and this set up will help accomplish precise, straight edges.
Agustina Beier (verified owner) –
It is just what I wanted. It grips firmly and doesn’t shift when cutting my plywood
Christophe Tillman (verified owner) –
This appears to be well-made but I never had to use it after I bought it.
Glennie Hills (verified owner) –
It works but very time consuming checking and double checking that the saw is aligned correctly as well as the saw offset is correct for the cutting once aligned with the guide. The buckles aren’t as robust as i’d hope they’d be and are too flexible to be able to hold the saw in place without movement. one of my buckles wasn’t completely assembled as it was missing a pin for the closure. luckily i was able to get a nail to fit for the purpose. I’m happy with the product and i feel it provided me with straight cuts. it just takes a long time for set up.