The Kreg Hex Shank Pocket-Hole Drill Bit is specifically for Kreg Joinery and use with any Kreg Jig. Features a 1/4 in. hex shank and compatibility with our Quick Change Chuck. Drills a standard 3/8 in. Pocket-Hole. Because the bit is 3/8 in. Dia and it can be used in any of our manual jigs.
- Hex-shank for use with quick change chuck
- Also works with standard chucks
- 3/8 in. Dia, high-speed steel
- 170 Dia pilot tip 1-piece, rugged design
- For use with all manual Kreg jig’s
WARNING: This product can expose you to chemicals including arsenic, which is known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov
Jermaine O’Keefe (verified owner) –
hopefully the tip doesn’t break on this bit
General Hermann (verified owner) –
Excellent bit that works well with the Kreg pocket hole jig. It also performs well in drilling pre-holes while creating a counter sink.
Velva Nader (verified owner) –
Shank pocket-hole bits are wonderful for quick change adapters. Much tighter grip in drill.
Vallie Harber (verified owner) –
All of my Kreg tools are easy to use and make my projects move quickly.
Kaylin Welch (verified owner) –
After 2 years of using my original bit it was time to replace it.
Palma Von (verified owner) –
I had previously been gifted with the non hex bit but getting this one I can pop it in my impact drill. I love my Kreg tool/accessories.
Alexandrea Frami (verified owner) –
I’ve had my Kreg Jig for less than a year, and the tip of my bit also broke off. I sent Kreg and email and they are sending me a replacement bit free of charge. They didn’t even ask a question, they just took care of it. This is the kind of service that makes any purchase worth it. I’m going to buy a spare just in case it breaks again in the middle of a project. At $15 and knowing that I’ll get great service if anything goes wrong, it’s totally worth it! Thanks Kreg!
Isaiah Terry (verified owner) –
Great tool
Josefina Spinka (verified owner) –
Works the way its supposed to
Evie Treutel (verified owner) –
Sharp gets the job done and leaves no frayed edges to the drilling holes. My last one lasted many years, and is still in good working order, I expect the same service from this drill bit.
Tyreek Lesch (verified owner) –
I have had a Kreg Pocket-Hole kit for about a year. It is a very handy tool to have, works quite well. I purchased this drill bit because the original bit broke at the small leading drill point. That is the only negative part of the system. I would still buy a replacement for this item if it broke.
Bernadine Heidenreich (verified owner) –
I still have the older version of this pocket drill bit and still sharp. I like the new design because of the hex shank. Thanks Kreg for redesigning this drill bit.
Flavio D’Amore (verified owner) –
Old bit broke. New bit is ok and sharper.
Alexandrea Hagenes (verified owner) –
Nice to be bale to replace just the parts you need and not have to purchase an entire new set.
Alexandre Johnston (verified owner) –
Just as good as the one that came with the jig.
Vincenza Gaylord (verified owner) –
Very sharp! :-DSo expensive. 🙁
Albin Leannon (verified owner) –
This guides itself well and is easy to use
Citlalli Ebert (verified owner) –
Perfect replacement for a bent Kreg bit late on a Sunday. Thanks, Home Depot!
Dorothea Hessel (verified owner) –
The bit is specially designed for the Keeg Jig, and it stays sharp. It makes pocket holes a snap!
Watson Crooks (verified owner) –
I had to buy this bit as my one that came with a Kreg Jig snapped the tip. This was only after a few uses so hopefully this one lasts longer.