Milwaukee 1-3/4 in. Hole Dozer Carbide Hole Saw
$17.28
The HOLE DOZER with Carbide Teeth hole saw delivers 50X life and thermal coating for reduced friction for heavy duty metal and multi-material uses.
In stock
Description
The MILWAUKEE HOLE DOZER with Carbide Teeth is the best hole saw solution for metal and multi-material applications. The hole saw provide 50X life in extreme metal and multi-material cutting compared to other bi-metal hole saws. A tough carbide-grade build is combined with a durable 4 TPI design, yielding the best carbide tooth durability and longest life in stainless steel, abrasive material and fastener-embedded wood applications. The HOLE DOZER has a cutting depth of 1.62 in., allowing clearance to handle cuts in a wide range of materials. Thermal coating on the saw reduces friction and drag during cutting. Cordless efficiency also allows for faster cutting in all applications. The hole sawslug is easy to remove with The Plug Jack, enhancing user productivity by providing the best access and leverage to remove material slugs.
- Milwaukee carbide teeth technology
- 4 TPI carbide teeth design gives best durability and longest life in extreme applications
- Thermoset coating reduces friction and drag, increasing overall speed and cordless efficiencies
- Plug-Jack T-slot’s enhance user productivity by providing best access and leverage to remove material slugs
- Cuts stainless steel, fastener embedded wood, cement board, fiberglass, plaster, asphalt shingles and more
- For the toughest applications where bi-metal hole saws cannot cut
- Includes: (1) 1-3/4 in. HOLE DOZER with carbide teeth
Additional information
| Weight | .18 lbs |
|---|---|
| Dimensions | 2.00 × 2.94 × 3.88 in |
| Arbor included | No |
| Bit Diameter | 3/8 in |
| Bit Length (in.) | 1.88 |
| Bit Material | Carbide |
| Drill Bit Type | Hole Saw |
| Drill Bit Type(s) Included | Hole Saw |
| Drilling Depth (in) | 1.62 |
| Hole Saw Diameter (in) | 1-3/4" |
| Individual/Set | Individual |
| Material Cut | Multi-Purpose |
| Min Chuck Size Required | 3/8 In. |
| Model | 49-56-0717 |
| Pilot Bit Included | No |
Reviews (78)
78 reviews for Milwaukee 1-3/4 in. Hole Dozer Carbide Hole Saw
Only logged in customers who have purchased this product may leave a review.
Related products
Drill Bits
Model# 282269
Drill Bits
Model# 48-20-8856
Drill Bits
Milwaukee 18 in. x 7/16 in. Bit Extension Bit Extention For Selfeed Bits and Hole Saws
Model# 48-28-4011
Drill Bits
Model# FB-005
Drill Bits
Model# FB-015
Drill Bits
Model# DW2045 G
Drill Bits
Model# 48-32-2100
Drill Bits
Bosch 20 in. Hammer Steel 1-1/8 in. Hex Moil Point Chisel for General Chipping Work
Model# HS2161
Jaylan Ritchie (verified owner) –
Works great. Was a replacement as my previous hole saw wore out
Florence Purdy (verified owner) –
These hole saw bits do a nice job. I drilled 10 consecutive holes in a row on a 1X6 board for a project that I was doing building a fishing rod holder. I can honestly say that the last hole I drilled was no more difficult than the first one. I drilled these holes with my battery operated drill. There were no issues drilling the holes other than the they did generate some heat, which is to be expected, but did not affect the performance. I’d recommend using these bits and they would particularly work well drilling through sheetrock or less dense materials.
Therese Kertzmann (verified owner) –
Great hole saw! Cuts through wood like butter! Just make sure to get the center drill with the prongs, with a hole saw this big, it will spin right off of a typical threaded center bit without the prongs to keep it from spinning on the threads. It fit my smaller hole saw center bit, but it unthreaded as soon as I stopped. This wasn’t a problem once I got the correct center bit with the prongs!
Gabriella Wunsch (verified owner) –
I used this with a BuildPro pipe coping tool. I used it on 1.5″ Stainless Steel Sch 40 pipe (1.9″ OD) and it worked awesome. I did use Tapmatic Edge lube, and let the hole saw do the cutting. I must have coped 50 pipes or more, without any issue. I did snap off one carbide tooth, but the it didn’t stop work. On such a hard material as 316 Stainless Steel, this was a small price to pay for so much work.
Ewald Denesik (verified owner) –
Cut 23 circular holes in metal 1/8 thick with no difficulty. Worked great
Reba Jacobs (verified owner) –
Doesn’t look like it but it goes right thru concrete. Works great !
Alta Glover (verified owner) –
Ordered this cutter to replace a worn out one. Perfect fit cuts great.
Nya Swaniawski (verified owner) –
I drilled 4, 7/8 inch holes through 1/4 steel. I used my drill press at 1000rpm, no lube, it drilled easily in about 20 seconds but the chatter and vibration from my drill press made it 1/16″ too big. I’m not 100% sure if it’s the bit or my press, but don’t make my mistake and test it in scrap first to test your hole.
Madelynn Lind (verified owner) –
does what Does what I need it to do.
Titus King (verified owner) –
Precision cuts. The quality is top notch.
Greg Bechtelar (verified owner) –
A little bit high in price but did the job
Lia Leffler (verified owner) –
Like hot knife thru butter
Hardy Renner (verified owner) –
Cut through stucco line butter. Perfect for cutting in new electric boxes.
Marlon Zboncak (verified owner) –
Did an excellent job cutting through thick stainless steel.
Angelina Hickle (verified owner) –
Very good
Gillian VonRueden (verified owner) –
Milwaukee makes excellent hole saws. If you need a 5″ hole saw for whatever application, this is what you need. Carbide teeth last a lot longer than bimetal teeth in most materials, especially when encountering metal, and is perfect to use in any wood or plastic application. Masonry, continuous use in metal, and similar materials you might want to consider a different saw. Fits standard hole saw arbors. Five stars for build quality and made in the USA.
Wayne Cronin (verified owner) –
the product worked just as expected. no issues at all.
Hildegard Schoen (verified owner) –
Great quality monster hole saw. Drilled smooth through some plywood for some exhaust vents for a roof job. It looks huge on a my drill. The carbide teeth definitely just chew through wood like a hot knife through butter. Of course I had to be careful because the larger a drill bit is, the more risky it is in a bind up. It did not bind up on me at all but still used it with caution. I really like Milwaukee’s pilot bit which I got separate because it has to knobs that secure into the large bit along with the threaded insert. I didn’t have any problem removing the wood from the bit after the cut out which I really liked. I only used it on wood but this hole saw is a beast. Definitely use a decently powered drill. It’s still really sharp and ready for more and even the paint itself held up which is pretty funny. Definitely recommend this line up Milwaukee hole saws because that carbide definitely makes a difference.