QEP 5/16 in. Pro Wet/Dry Diamond Hole Saw
$18.87
Rebuild some greatness to your floors without any effort with the assistance of this extraordinarily designed QEP 5/ Pro Wet/Dry Diamond Hole Saw.
In stock
Description
The QEP 5/16 in. Wet/Dry Diamond Drill Bit is designed for the easy, fast and accurate cutting of porcelain, ceramic and glass tiles. This hole saw features a special diamond grit edge for faster and smoother cuts, while using less water than conventional diamond drill bits. Simply dip the hole saw into water and drill the desired hole for professional quality and results.
- Ideal for cutting 5/16 in. holes in ceramic, porcelain and glass tiles with minimal water use
- Advanced metallurgical technology bonds diamond grit to chrome alloy steel base to produce a long-lasting cutting edge
- Extremely durable and built to last longer than conventional diamond drill bits and standard hole saws
- 12 times longer lasting than standard hole saws
- Simply dip in water, no need for a constant water delivery system, for quick and easy use
- Flexibility to be used in wet or dry cutting conditions is preferred by professional flooring installers
- Easy to clean by rinsing with hose or in clean water after each use
WARNING: This product can expose you to chemicals including arsenic, which is known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov
Additional information
| Weight | 0.026 lbs |
|---|---|
| Dimensions | 0.75 × 2.75 × 7.00 in |
| Blade Length (in.) | 0.3125 in |
| Blade Material | Diamond |
| Blade Width (in.) | 0.3 |
| Hand Tool Type | Blade |
| Individual/Set | Individual |
| Model | 10080 |
| Number of Pieces | 1 |
| Product Length (in.) | 0.3 in |
| Replacement Blade Type | Fixed Blade |
| Teeth Per Inch | 0 |
| Tools Product Type | Power Tool |
Reviews (15)
15 reviews for QEP 5/16 in. Pro Wet/Dry Diamond Hole Saw
Only logged in customers who have purchased this product may leave a review.
Related products
Knives & Blades
Milwaukee General Purpose Utility Blades with Dispenser (100-Piece)
Model# 48-22-1900
Knives & Blades
Stanley Surform 5-1/2 in. Pocket Fine-Cut Plane Blade Replacement for 21-399
Model# 21-398
Knives & Blades
Model# 46037SEN
Knives & Blades
Model# 10-989
Knives & Blades
Model# 10-788
Knives & Blades
Model# 122CS6
Knives & Blades
Model# 10-189C
Knives & Blades
Klein Tools 6-1/2 in. Cable-Splicers Knife with 1-3/4 in. Blade
Model# 44200
Christiana Corwin (verified owner) –
The 5/16 inch Pro Wet/Dry Diamond Drill Bit # 10080Q is a very sharp bit fore using on tile with a lot of water to help keep it from getting hot. The best way to use the bit I found was to use it at high RPMs (over 3500) with cold water, moving at a very slow speed. The bit I feel is a one and done bit, meaning it is a one time use bit. The bit is recommended for the cost, and quality.
Blake Bauch (verified owner) –
I drilled about 10 holes through some very hard, thick porcelain tile and the cement backer board to mount a shower door. I closely followed the directions, and the drill bit made it through this job. I don’t know if it would last through another set of holes, though. The aluminum barrel has shown signs of thinning and wear behind the diamond area, since it’s best to rock the bit a little while drilling to help it to bite, and it rubs on the sides of the hole when doing so. Apparently frequent dipping of the bit in water is sufficient to cool it and clean it to make it last a while without a continuous flow of water. The bit did what I needed it to do, but I’m thinking of it as an expendable tool.
Neva Harris (verified owner) –
Good drill bit
Sammy Fisher (verified owner) –
This QEP drill bit is very easy to control when positioning the bit to start the hole in the tile, drills clean holes and seems to be a lot more durable than conventional ‘spade’ shaped tile bits I have used. Drilling into tile can be laborious and also risky in as much as you can damage the tile if the drill bit skids over the tile surface when starting the hole however these bits are a real confidence builder in this respect. Its the first time I’ve tried one of these and I would highly recommend it.We recently installed a small grab handle in our bathroom to make it safer to get in and out of our deep soaker tub. We remodeled our bathroom recently and put some 1/4″ thick ceramic tile over 1/2″ cement board. I previously used a more conventional spade shaped tile drill to drill holes for our shower door and was looking for an alternative that is easier to control and more durable than a spade bit.This QEP bit is very easy to use if you follow the very simple instructions. Have a small bowl of water handy to keep dipping the drill bit in to keep it cool and lubricated and you will have no issues. To start drilling a hole, you angle the bit at 45 degrees and have the drill on full speed before contacting the tile. A firm grip will stop the drill from skating over the tile and after a few seconds you can change the drill angle to be square to the tile and drill the hole conventionally.Every few seconds you should take the bit out of the hole and dip it in water to keep it lubricated and cooled. In my case, if it dried out, a puff of tile dust would be forced out of the hole letting me know it was time to dip the bit into the water.I drilled 5 holes and the fifth was as easy to drill as the first so the drill is certainly durable. By comparison I obliterated a spade tile bit after a couple of holes when hanging the shower door in the same ceramic tile a few months ago.Between each hole, I used a smaller drill bit to clean out the tile residue from the inside of the tile bit. This stopped the center of the drill plugging up with the tile and backer board core it was removing. I also found that the bit was less prone to ‘wandering’ and gave straight, true holes when the bit was progressing through the different material in the hole. When I was drilling with the spade bit, I found it would go awry when I made it through the tile and into the cement backer board and I had no such issues with this QEP drill bit.
Camila Kuhn (verified owner) –
I will never use a spade bit again. This is the way to go.
Murray Powlowski (verified owner) –
I got one of these because am doing a bathroom reno using travertine tile from the floor to the ceiling. So in need of something to drill holes for passing electrical wiring through and such, and this little guy works quite well. You have to follow the instructions however and come in at an angle very delicately to start your groove cut or the bit will dance all over your tile.
Fredrick Beer (verified owner) –
Works with water or without
Mable Lang (verified owner) –
Did the job clean and efficient.
Curt Von (verified owner) –
I was able to drill 20 holes in ceramic tile with this one drill.
Adah Homenick (verified owner) –
Cheaper hole saws gave out after 2 porcelain holes. This PRO version is the way to go. Don’t buy cheap hole saws – they will waste your time and money.
Jacinthe Haley (verified owner) –
The Wet/Dry Pro Diamond Drill Bit is sturdy and cuts well. It comes with very detailed instructions, which I found very helpful, such as starting at an angle to keep it from slipping, and to dip the bit in water frequenty to cool it down. I needed to replace a sliding bathroom closet door, after replacing vinyl with tile, which required having a hole through it. Rotating the position, taking it slow with small cuts and following the instructions will give the best result.
Leopold Kautzer (verified owner) –
Excellent, Excellent and Excellent. Drilled three holes in hard ceramic tile and it took only about 5 minutes. Previously I had tried three holes with a carbide tipped drill bit and it took 4 hours and I was exhausted when finished. This was the best money I have ever spent for a tool. Highly recommend it.
Nico Osinski (verified owner) –
One of the toughest jobs to do is drill a straight clean hole in your ceramic tile. If you’re installing a new shower door or a shelf in the shower, this bit is what you need to get the job done. The diamond chips make cutting through the glaze layer very easy. Important to follow the instructions carefully. Holding the bit at an angle to get started takes some practice, but once you start through the glaze, ease up to perpendicular and you’re home free. A helpful tip, I take an old sponge put a hole in it, soak up some water. Once I start drilling I slip the bit through the hole in the sponge and use the water to keep the bit cool. This will extend the bit life. Once through the glaze layer the bit goes through very easily. You’ll have a nice clean hole to put your anchors in.
Mabel Barrows (verified owner) –
functioned well, life was short
Kaelyn Doyle (verified owner) –
I obtained this bit to drill holes through the porcelain tile in our shower and tub enclosures so that I could hang hooks and soap dishes. I have always used a wood template to start the holes when using a diamond hole saw. The instructions on the package said to start the bit at a 45 degree angle and a high speed without a template. This worked very well. With the template it is hard to see if you are actually drilling in the right location but with this method you can see your marks. When I finished the hole I was impressed with the quality. It is a very clean hole with no chipping of the tile surface. I haven’t used the bit enough to speak to the long life but after two holes I could not see any change in the speed of cutting. As with all diamond bits I do use lots of water for cooling and lubrication.